鹽城市薄膜開關按鍵絲印機玩具外殼移印機油漆桶絲網印刷機功能齊全
第一種:半自動時未踩腳踏開關而立即動作。此類故障原因多半是腳踏開關損壞或腳踏開關插座進水導致短路造成,另一個是手動起動按鈕開關有問題。
解決方法:更換新的開關、插座、按鈕開關或拆開維修相關損壞件。
第二種:半自動工作時踩腳踏開關滑座下降,放開后又上升。這種現象一般是橫滑座左側接近開關損壞或斷了連線。
解決方法:更換接近開關或接通開關連線。
第三種:半自動工作時踩腳踏開關立滑座下降,印刷座左移后即不動作。這種故障發生原因有橫滑座左側接近開關未感應到或有問題。還有腳踏開關內微動開關卡住不動作,也會(huì )引起此故障。
解決方法:調整好左側接近開關感應點或更換好的接近開關,將腳踏開關內的微動開關調整、修復或更換新的微動開關。
第四種:半自動工作時踩腳踏開關,滑座下降左移后上升但不右移。絲印機出現這種現象的發生是立滑座左上方接近開關未感應到或接近開關有問題。
解決方法:調整上方接近開關感應或更接近開關。
第五種:動作切換后上升動作慢半拍。此類故障是控制電磁閥有異物阻塞或電磁閥有故障。
解決辦法:拆除磁閥清理或更換好的電磁閥。
第六種:手動、半自動全部不動作,電源燈亮。此類故障原因有低壓側保險絲燒斷,無氣源進入,電磁閥全部都有故障。
解決方法:換低壓側保險絲,檢查壓力是否達到4-7kg/cm,電磁閥全部故障很小,多半是連線斷。
第七種:自動、半自啟動不下降。此類故障發生是橫滑座右側接近開關有故障或未感應到、選擇開關故障、單動開關連鎖點損壞。
解決方法:調整接近開關感應或更換右側接近開關,更換或修復選擇開關及單動開關。
第八種:自動無法啟動,此類故障是上、下氣缸的微支開關常閉,接點無法導通或計時器損壞。
解決方法:修復微動開關,或更換好計時器。
第九種:工作臺面不吸氣,此類故障原因是吸氣馬達燒了??刂岂R達運行的接觸器損壞、吸氣馬達轉動,但控制吸氣電磁閥故障、吸氣選擇開關故障。
解決方法:修復或更換。
第十種:工作臺面不吸氣,原因是吸所控制電磁閥壞或內部塊損壞。
解決方法:更換修復。
第十一種:立滑座上升速度緩慢,原因是立滑座軸承無油或氣缸活塞磨損,磁撞使軸心彎曲。
解決方法:補給油、更換活塞口令,調整軸心。
以上是絲印機日常作業時經常會(huì )出現的故障,熟悉掌握以上的解決方法可以確保生產的正常運作。