全自動絲印機的常見故障
全自動絲印機在印刷進程種總是會(huì )存在著各種毛病成績,如手動、半自動全部不工作、電源燈亮、印刷座左移后即不工作等等。
第一種毛病景象:自動無法啟動,此類毛病是上、下氣缸的微支開關常閉,接點無法導通或計時器損壞,處理辦法是修復微動開關,或改換好計時器。
第二種毛病景象:半自動工作時踩腳踏開關滑座下降,放開后又上升。
這種景象普通是絲印機橫滑座左側接近開關損壞或斷了連線,處理辦法是改換接近開關或接通開關連線。
第三種毛病景象:半自動工作時踩腳踏開關,滑座下降左移后上升但不右移。這種景象的發作是立滑座左上方接近開關未感應到或接近開關有成績,處理辦法是調整上方接近開關感應或更好的接近開關。
第四種毛病景象:任務臺面不吸氣,緣由是吸所控制電磁閥壞或外部塊損壞,處理辦法是改換修復。
第五種毛病景象:工作切換后上升舉措慢半拍。此類毛病是控制電磁閥有異物阻塞或電磁閥有毛病,處理方法是撤除磁閥清算或改換好的電磁閥。
第六種毛病景象:立滑座上升速度遲緩,緣由是立滑座軸承無油或氣缸活塞磨損,磁撞使軸心彎曲,處理辦法是補給油、改換活塞口令,調整軸心。
第七種毛病景象:半自動工作時踩腳踏開關立滑座下降,絲印機的印刷座左移后即不工作。
這種毛病發作緣由有橫滑座左側接近開關未感應到或有成績。處理辦法是調整好左側接近開關感應點或改換好的接近開關;還有腳踏開關內微動開關卡住不工作,也會(huì )惹起此毛病。處理辦法是將腳踏開關內的微動開關調整、修復或改換新的微動開關。
第八種毛病景象:手動、半自動全部不舉措,電源燈亮。此類毛病緣由有高壓側保險絲燒斷,無氣源進入,電磁閥全部都有毛病。處理辦法是換高壓側保險絲,反省壓力能否到達4-7kg/cm,電磁閥全部毛病很小,多半是連線斷。
第九種毛病景象:半自動時未踩腳踏開關而立刻工作。
此類毛病緣由多半是全自動絲印機的腳踏開關損壞或腳踏開關插座進水招致短路形成,另一個是手動起動按鈕開關有成績。修復辦法是改換新的開關、插座、按鈕開關或拆開維修相關損壞件。
第十種毛病景象:任務臺面不吸氣,此類毛病緣由是吸氣馬達燒了。
控制馬達運轉的接觸器損壞、吸氣馬達轉動,但控制吸氣電磁閥毛病、吸氣選擇開關毛病,處理辦法修復或改換。
第十一種毛病景象:自動、半自啟動不下降。此類毛病發作是全自動絲印機的橫滑座右側接近開關有毛病或未感應到、選擇開關毛病、單動開關連鎖點損壞。處理辦法是調整接近開關感應或改換右側接近開關,改換或修復選擇開關及單動開關。